The Smith Chart
The Smith chart is a tool for solving impedance matching problems on radio-frequency lines. This link also contains a high-resolution diagram to print and use…
https://www.electronics-engineering.com/en/the-smith-chart/

The Smith chart is a tool for solving impedance matching problems on radio-frequency lines. This link also contains a high-resolution diagram to print and use for the exercises
The Smith chart is a very widely used tool for solving all radio-frequency line matching problems.
The SMITH chart is a circular diagram made up of two sets of intersecting circles that allow you to determine the impedance, or more often the admittance, in its real and imaginary components, of the line at any point.
It is therefore possible to choose the right point along the line at which to insert the stub that compensates the unwanted reactive part of the load and lets the generator see only its resistive part, so that no unwanted reflected waves are produced.
A load can also be matched if it is only resistive, but of a value different from that of the line.
Matching is also possible with two different stubs placed at suitably calculated distances from the load.
With the chart you can also calculate the length that each individual stub must have, case by case.
The chart also gives the reflection coefficient r at the load and at every point of the line, and the VSWR at every point of the line and at the load.
With the chart you can convert an impedance into the corresponding admittance at a glance.
You can plot the standing-wave diagram, determining both the VSWR and the position of the maxima and minima with respect to the load.
The Smith chart can be used working either with impedances or with admittances.
In any case, all quantities are normalised, that is expressed as a ratio between the load impedance and the characteristic resistance of the line, or as a ratio between the load admittance and the characteristic admittance of the line.
There are therefore no values in ohms or in siemens, only pure numbers.
MATLAB ALGORITHM (WITH AN EXAMPLE RUN) AS A REPLACEMENT FOR THE SMITH CHART
Excellent algorithm that solves single-stub matching problems without using the Smith chart
Running the program
» princ
IMPEDENZA DI LINEA
Assegna il valore dell'impedenza caratteristica (in ohm): 50
Assegna il valore dell'impedenza di carico (in ohm): 60+25i
E' possibile mettere uno stub induttivo che ha (in s):
ammettenza = 0 - 0.4916i
che presenta una distanza dal carico (normalizzato a lamda):
distanza = 0.2211
INDICARE ADESSO IL TIPO DI STUB
1: lo stub è in corto-circuito
2 (o altro): lo stub è in circuito aperto
1
l'ammettenza iniziale dello stub è infinita
La lunghezza dello stub (normalizzata a lamda) e:
lunghezza = 0.1773
inoltre è possibile mettere uno stub capacitivo che ha (in s):
ammettenza = 0 + 0.4916i
che presenta una distanza dal carico (normalizzato a lamda):
distanza = 0.4328
INDICARE ADESSO IL TIPO DI STUB
1: lo stub è in corto-circuito
2 (o altro): lo stub è in circuito aperto
2
l'ammettenza iniziale dello stub è nulla
La lunghezza dello stub (normalizzata a lamda) è:
lunghezza = 0.0727LinSmith GPL Software
Using the Smith chart to calculate and check the impedances of a transmission line often involves graphical difficulties, especially in complex situations such as the presence of several load impedances and/or discrete components inside a line.
All the calculation operations, and the corresponding graphical output, can alternatively be entrusted to software that solves every required step more quickly and accurately: linSmith. Written for the Linux operating system under the GPL licence, linSmith returns the numerical results of every single step in the development of the calculation and handles the representation of the various parameters involved by redrawing them on the non-normalised Smith chart.
Here are some salient features:
- Definition of multiple load impedances (for different frequencies)
- Use of discrete components (L, C and various combinations) and line elements (stubs, etc.)
- Series and parallel connections
- Use of real, non-normalised impedances on the chart
- Direct display of the results on screen
- Generation of a PostScript graphics file
- Creation of a detailed log of all the calculation operations carried out
Although the software was created for teaching purposes, it is also very well suited to the practical purposes of calculating and checking the impedance of transmission lines for amateur radio use.






Sono l'autore di questa pagina su «La Carta di Smith». Se qualcosa non è chiaro, se vi serve un esempio in più o volete approfondire un punto, scrivetelo qui sotto nei commenti: rispondo personalmente. Se la pagina vi è stata utile, lasciate un voto con le stelle in cima all'articolo.